Produse pentru neti pot solution (12)

Oxyde de potassium (K2O) soluble dans l'eau : 33 % Azote total (N) : 2 % Azote uréique (N) 2 % EDTA (acide édétique) : 2 %

In many plastic systems, such as elastic PVC floor coverings, a wide variety of Incorporated inorganic fillers. However, these inorganic additives do not show any significant tendency to be incorporated into the liquid constituents of a plastisol. Without suitable additives, this is practically impossible. Provides for an optimal distribution of the filler NEWOS for the process step of dispersing innovative and market-proven process aids under the name NEWOTEC.

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Tube | 5 ml Liquid Medium IVD | Sterile | pH 7.4 ± 0.2 Packaged in 25 - 50 units Storage 2-12 °C Shelf life 5 months Nutrient Tube Medium is a liquid medium used for the growth of various microorganisms. Some fastidious microorganisms may not be able to grow in this medium. Product Code: AKL-399

Testicular peptides. Peptides have a selective action on male reproductive system cells, increase their functional activity and enhance mobility of spermatozoa. Bulk:60 capsules of 0,215 g. Brand:Cytomaxes Catalog item:Testoluten Expiry date:28.02.2027 Barcode:4603423006268

DETAILING & PAINT CORRECTION

Mineral Plus

NEDEX adsorbent ‘NANOMOL’ is a mixture of calcium oxide containing natural desiccants and natural binders. The product is designed for a static water adsorption process with very low adsorption speed. With an optimized density it can reach very good water adsorption capacity in a specific volume. It has no chemical reactions to aluminium, steel, galvanized steel and plastics. NANOMOL has even higher water adsorption capacity and Delta T compared to MULTIMOL. NANOMOL is an adsorbent for insulating glass units with specifications according to EN 1279:2018. Features: Very low gas desorption values Very high water adsorption capacity Granulation without broken particles and Zero dust content

Micro Tube SafeFit, 5.0 ml with Cap

Composition chimique (p/p) Oxyde de calcium (CaO) soluble dans l'eau : 12 % Oxyde de calcium (CaO) complexé à l'acide lignosulfonique : 6 % pH : 2,5 – 2,7 Formule Liquide Emballage Conditionnement de 5, 25, 220 et 1000 litres

Eye tissues peptides. Peptides have a selective action on various eye tissue cells and normalize their metabolism. Bulk:60 capsules of 0,215 g Brand:Cytomaxes Catalog item :Visoluten Expiry date:31.01.2027 Barcode:4603423005674

Urine Cup 100 ml with Screw Cap, irradiated